Satin Finishing Wax For Wood

Satin Finishing Wax is a special blend of waxes designed to give finished woods a rich luster. It can be used as a polish for rubbing out new finishes or as a scratch-remover for worn surfaces. It works well over oil and water-based finishes, including Danish Oil. We recommend a wet-sanding process followed by buffing to a soft silky sheen. Satin Finishing Wax is a PFAS-free wood finish and maintenance formula. As General Finishes strives for a cleaner and healthier environment, all future product development will be free of “Forever Chemicals." 

General Finishes Satin Finishing Wax, 16 oz Bottle

Instructions

How To Apply General Finishes Satin Wax

General Finishes Satin Wax Application Steps

Light Polishing:

  1. Shake container well.
  2. Wipe on a thin, even coat with a clean cloth.
  3. Let sit 10 minutes.
  4. Polish with a soft cloth, wiping away the excess in the direction of the wood grain.

Buffing A Topcoat To A High Gloss:

  1. Shake container well.
  2. Wipe on a thin, even coat with a clean cloth.
  3. Let sit 1-2 minutes.
  4. Buff off excess with a buffing or sanding pad (see below) in the direction of the wood grain. The higher/finer grit you use, the easier it will be to achieve a high-gloss finish.
  5. Buffing Tools:
    1. Norton Abrasives, Yellow Block
      • 1000-grit, 1500-grit, 2000-grit
      • Creates a high-gloss finish
    2. Klingspor Fusion Pads
      • 2800- to 3500-grit
      • Ideal for painted and gloss finishes
    3. Klingspor Superfine Sanding Pad
      • 220-grit
      • General purpose option for rubbing out topcoats and paints with a flat or satin sheen
    4. Merka Mirlon Pads
      • Total 1500 (gray)
      • Total 2500 (gold)
      • Ideal for oil-based finishes or between coats of paint

Fixing A Scratch:

  1. Shake container well.
  2. Do not sand "dry-on-dry" to remove scratch marks.
  3. Add Satin Wax as a lubricant on the pad AND on the surface of your project, then spread smooth with a rag.
  4. Let sit 10 minutes.
  5. Polish with a soft cloth, wiping away the excess in the direction of the wood grain.

Storage of Maintenance Products

Life of Product
Maintenance products are best used within 1 year of the manufacture date listed on the bottom of the can. The following best practice will increase the life of your product:

Store in moderate temperatures of 50-100°F/10-38°C. Heat-damaged product cannot be revitalized. Temperature-controlled spaces, such as a basement, are ideal for storage. Do not store product in an attic, garage, in direct sunlight, or next appliances with heat or flame such as a furnace.

Warnings, Personal Protection & Warranties

Compatibility
Do not use water-based products with Linseed Oils or Danish Oils.
 

Limited Warranty
General Finishes products must be tested to your complete satisfaction before using. General Finishes will not be responsible for color satisfaction, misapplication, nor compatibility with other manufacturers' products. General Finishes will be responsible only for the cost of our products, and not for costs such as labor, damage or project replacement. 

Contamination and Compatibility
Our finishes are engineered as a system and are compatible with each other. General Finishes cannot guarantee an ideal refinish when applying our products on top of or combined with another company's products or over surfaces that have been in contact with waxes, polishes or sprays containing contaminants such as silicone. Test for adherence and aesthetics before beginning. 

Warning
If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log onto www.epa.gov/lead.

FIRST AID:
Seek immediate medical attention if symptoms occur due to the following. EYE CONTACT: Remove any contact lenses. Flush eyes with water for 20+ minutes while lifting upper and lower eyelids. SKIN CONTACT: Wash thoroughly after handling. INHALATION: Move to fresh air and loosen clothing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. INGESTION: Call physician immediately. Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. 

Warning
This product contains a chemical known to the State Of California to cause cancer and birth defects. Do not swallow; first aid: drink water to dilute product. May cause eye or skin irritation; first aid: flush eyes thoroughly with water.

Warning
Keep out of reach of children. Avoid contact with eyes. Keep container tightly closed when not in use. Wash thoroughly after handling.

PERSONAL PROTECTION DURING USE:

Hand protection
Chemical-resistant, impervious gloves complying with an approved standard should be worn when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves still retain their protective properties. It should be noted that the time to breakthrough for any glove material may differ for different manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated.

Eye protection: Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases, or dust. If contact is possible, the following protection should be worn unless the assessment indicates a higher degree of protection: safety glasses with side shields.

Respiratory protection:
Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important use aspects.


Body protection Personal protective equipment for the body should be selected based on the amount and repetition of exposure. It should be approved by a specialist before handling this product.

Environmental exposure controls:
Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation.

Appropriate engineering controls:
Good general ventilation should be sufficient to control worker exposure to airborne contaminants.

Hygiene measures: 
Wash hands, forearms, and face thoroughly after handling chemical products, before eating, smoking, and using the lavatory, and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.
 

Other skin protection: Appropriate footwear and any additional skin protection measures should be selected based on the task being performed.

Specifications

Basic Features
Product Colors Clear
Ambering No
Interior or Exterior Interior
Type Accent Wax
Application
Application Method Wipe On with Clean Rag
Usable over existing finishes Yes
Sprayable No
Contents
Can Sizes 8 oz. bottles
Technical Data
VOC US VOC
645.446 g/L

FAQs

Satin Finishing Wax FAQs

*How Should I Clean My Finished Project?

After your finish has cured, the best way to clean is with a water-damp rag. If your surface requires deep cleaning due to grease or grime build-up, add a speck of a strong dish detergent, such as Dawn or a bit of vinegar to your damp rag.

If need deeper cleaning, use General Finishes Orange Oil Polish.

Avoid using oil-soap or silicone-based daily cleaners or dusting sprays These products and the chemicals in other cleaners can contaminate your finish, preventing adhesion of future finishes. 

NOTE: Do not clean furniture until the finish has cured completely. 

Cure Time Guidelines: 

  • Water Based Finishes: 21 days
  • Oil Based Finishes: 30 days 

Related Categories


*How Do I Buff Out High Performance Water Based Topcoat to a High Gloss?

There are several techniques by Jeff Jewitt of Homestead Finishing Products:

DRY BUFF WITH MIRKA ROYAL MICRO PAPER

Using Mirka Royal Micro sandpaper, always start with 1500-grit sandpaper. Begin with a small area, make 2-3 passes, then evaluate results. Go to a heavier grit if surface irregularities are not fully removed. Finish with 1500-grit paper.

DRY/WET BUFF WITH ABRALON POLISHING DISCS

Start by dry sanding with Abralon 2000-grit, and then 4000-grit. Start slowly, monitor to see if buildup is occurring. A large sized table might take 5-25 sheets of paper.

If needed, lubricate by moistening with General Finishes Satin Finishing Wax, mineral spirits, or naphtha. Never use water as a lubricant.

If lubricated, one sheet of 1000-grit or 1500-grit should do the entire table.

BUFFING/POLISHING WITH PRESTA POLISHING KITS

Spray Presta polish on buffing pad stuff to lubricate the pad. Apply a quarter-sized dab of polish to sand one section. Spread with pad. Continue section by section. Mist buffing pad with Presta lubricating material when it gets too dry. You should be able to use a buffing pad on 10-20 tables before washing and reusing.
 
When done, mist entire surface with and buff with a micro-cloth to remove splatter

NOTE: Never wet sand a water-based finish.

Related Categories


*How Do I Remove Wax from an Existing Finish?*

Even though there is internet chatter about removing wax with 3rd party products, mineral spirits or vinegar, none guarantee success.

There is an old saying in the industry. "Once you wax, you cannot go back". Nothing adheres well to wax and even after cleaning, the wood grain can become contaminated. Wax can penetrate the wood, making future paint or stain finishes or touch-ups difficult or impossible.

The risk of a failure in re-coating over a wax finish is very high. Your best bet is to clean, strip, and sand, but even that is problematic. Here is what we recommend if you want to go ahead.

  1. Scrub with a solvent, such as mineral spirits, to break the wax barrier. Follow with several applications of Acetone applied with gray scotch bright pads to scrub the surface.
  2. Then strip the surface. You want to remove as much wax as possible before sanding to minimize the risk of driving the wax into the grain of the wood from the friction of sanding.
  3. Strippers that contain Methylyne Chloride like Zip Strip or Savograns are aggressive strippers but harsher. Gentler strippers are citrus or soy-based such as Citrus Strip or Soy Gel.

After cleaning, test the first coat of finish for adhesion. Rub a nickel across the surface or scrape the first coat lightly after 24 hours with a moderately sharp object such as a blunt standard table knife, not a sharp or serrated knife.

If you are finishing as a professional, NEVER guarantee a finish applied over wax. Here is a suggestion for your contracts:

We cannot warrant finishes over an existing piece of furniture. If products containing silicone (such as dusting sprays), oil soaps or waxes have been previously used on the piece, they may contaminate a new finish and prevent adhesion. In these situations, it is best to strip and sand the entire piece. Occasionally, a previous wax finish or silicone may be impossible to completely remove.

________ (Initials) I acknowledge that this piece has never been waxed/polished with a silicone-based dusting spray or cleaned with oil soaps.

________ (Initial) I have no knowledge of previous cleaning products used but realize they may have been applied by previous owners.

Related Categories


*Which Is Better as a Sealer? Topcoat or Wax?

It depends on whether you are looking for aesthetics or durability.

A topcoat will provide greater durability and protection than wax finishes over time.

While wax finishes are lovely, they typically show wear (fingerprints) and are not permanent, requiring semi-annual to annual maintenance.

Wax is a low durability finish. It’s fine for a decorative piece that will receive light traffic. It is absolutely not strong enough for tables, kitchen cabinets, or other surfaces that will see frequent use.

Wax takes a bit of elbow grease to apply.

Furthermore, nothing adheres well to wax, which can impact future finish changes. Even though there is internet chatter about removing wax with 3rd party products or mineral spirits, the risk of a failure in re-coating over a wax finish is very high and sometimes impossible.

If you love a wax finish, try General Finishes Satin Finishing Wax. If you want the look and feel of wax with more durability, use our General Finishes Flat Out Flat Topcoat. For even more protection, use General Finishes High Performance Topcoat.

Related Categories


Can Gel Stain be sealed with wax instead of top coat?

Wax can be used over Gel Stain, if you prefer. Just let the Gel Stain dry 24-48 hours before applying the wax. Note: wax is not a durable product. It needs yearly reapplication, will show daily use (finger marks and smudges) and may be very difficult to remove if a future topcoat application is desired.

Related Categories


Can Glaze Effects be sealed with wax instead of top coat?

Yes, you can use Satin Wax instead of top coat if you prefer. Although GF loves the look of wax, we recommend using top coat because wax is not as durable. Wax requires annual maintenance and it must be removed if you want to apply topcoat in the future.

Related Categories


Should I Use Satin Wax to Seal My Kitchen Cabinets?

You can...we do we do believe that wax can be a beautiful addition to many projects. However, it is best not to use wax in high-use temperature-dependent situations like kitchens or bathrooms.

Furthermore, kitchen cabinets require long-term protection and high-quality resistance to wear. Wax provides far less protection and durability than an engineered resin based top coat like High Performance or any of our professional Enduro Spray finishes. A particular problem are range hoods and dishwasher panels - wax cannot stand up to the heat and may melt and run.

Wax finishes typically show wear (ex: fingerprints) and require semi-annual to annual maintenance. Furthermore, touch-ups or changes are impossible once wax has been added to the surface because no finish will adhere well to wax. Even though there is internet chatter about removing wax with 3rd party products or mineral spirits, the risk of a failure in re-coating over a wax finish is very high. Resin-based topcoaats can be removed or covered with a new finish without a problem if you ever decide to touch-up or refinish your cabinets in the future.

Related Categories


What Finishes & Coatings does General Finishes Offer for Retailers, Homeowners and DIY??

General Finishes offers water, oil, and maintenance finishes that meet the needs of homeowners, woodworkers, and DIY’ers. Comprehensive videos are available for each product on YouTube, plus dynamic comparison charts at GeneralFinishes.com/COMPARE.

All General Finishes water-based finishes are:

  • VOC compliant in all 50 states
  • Water cleanup 
  • Low odor
  • Non-flammable
INTERIOR PRIMERS

Water Based Stain Blocker is:

  • An epoxy acrylic formulation.
  • Prevents tannin bleed-through & discoloration.
  • Has high build with excellent adhesion properties.
  • Apply with a brush, roller, or sprayer.
WATER-BASED TOPCOATS & PIGMENTED FINISHES

High Performance Water-Based Topcoat is:

  • An Interior polyurethane/acrylic blend.
  • Clear drying.
  • highly resistant to water and household chemicals.
  • Apply with a brush or sprayer.

Flat Out Flat Water-Based Topcoat is:

  • An interior acrylic formulation.
  • Clear drying.
  • provides an extremely flat finish with high durability.
  • Apply with a brush or sprayer.

Enduro-Var II Water-Based Topcoat is:

  • An interior oil-modified water-based urethane.
  • Dries to a light, amber tone.
  • Made with over 50% renewable resources.
  • Apply with a brush or sprayer.

Water-Based Milk Paint is:

  • A premium interior and exterior-rated acrylic formulation.
  • Self-sealing and does not require topcoat.
  • Is made with over 50% renewable resources.
  • Is available in 12 popular colors, plus two tint bases.
  • Apply with a brush, roller, or sprayer.

Water-Based Glaze Effects is:

  • An interior oxidating acrylic formula.
  • Available in 6 colors, including a Clear Base.
  • Is a decorative specialty finish.
  • Can be intermixed to create custom colors.
  • It requires a topcoat
  • Apply with a brush, roller, or sprayer

Pro Image Water-Based Flooring Topcoat is:

  • An interior polyurethane.
  • Clear drying.
  • Levels to a smooth, hard, durable finish.
  • Provides excellent slip and black heel mark resistance.
  • Apply with a brush, roller, or pad applicator.
INTERIOR WATER-BASED STAINS

Water-Based Wood Stain is:

  • Made with over 50% renewable resources.
  • It’s available in 18 deep brilliant colors.
  • And provides universal coverage on many wood species.
  • Apply with a brush or sprayer.

Water-Based Pre-Stain Conditioner is:

  • Used to control blotching on hard-to-stain woods.
  • And to reduce Water Based Wood Stains.
  • Apply with a brush or sprayer.

Water-Based Dye Stain is:

  • A penetrating stain with ink-like consistency.
  • It is available in 14 vibrant colors.
  • And can be used as a toner.
  • Apply with a brush or sprayer or wiping on.

Water-Based Dye Stain Reducer is:

  • The clear base used to reduce Dye Stain colors.
WATER & OIL EXTERIOR FINISHES

Exterior 450 Clear Water-Based Topcoat is:

  • A polyurethane formulation.
  • Tintable to dark colors.
  • Contains UV absorbers & Mildewcides to protect the finish.
  • Clear drying.
  • Apply with a brush or sprayer.

 450 White Water-Based Topcoat is: 

  • A pigmented polyurethane formulation.
  • Is tintable to light and pastel colors.
  • Contains UV absorbers & mildewcides to protect the finish.
  • Apply with a brush, roller, or sprayer.

Exterior 450 Water-Based Stain is:

  • Made with over 50% renewable resources.
  • Available in 10 colors, including a clear base.
  • Contains U.V. absorbers & mildewcides to protect the finish.
  • Apply with a brush or sprayer.

Water-Based Milk Paint is:

  • A premium Interior and exterior-rated acrylic formulation.
  • Self-sealing and does not require topcoat.
  • Made with over 50% renewable resources.
  • Available in 12 popular colors, plus two tint bases.
  • Apply with a brush, roller or sprayer.

Outdoor Oil is:

  • A penetrating oil wood preservative.
  • Contains UV absorbers and mildewcides to protect the finish.
  • This finish will amber as it ages.
  • A maintenance product. Reapply when wear becomes evident.
  • Apply with a brush, roller or sprayer.
INTERIOR OIL STAINS & AMBERING TOPCOATS

Gel Satin Oil-Based Topcoat is:

  • A heavy-bodied, no-drip oil and urethane formula.
  • Designed to provide a hand-rubbed look.
  • Will amber as it ages.
  • Apply with a brush or wipe on.

Gel Oil-Based Stain is:

  • A heavy-bodied, no-drip formula.
  • Available in 14 deep, rich, uniform colors.
  • Apply with a brush, roller, or wipe on.

 Arm-R-Seal Oil-Based Topcoat is:

  • A penetrating sealer with a high-quality urethane formulation.
  • It provides long-lasting, durable protection.
  • and works beautifully on projects with detail.
  • This finish will amber as it ages
  • Apply with a brush or wipe on.

Liquid Oil-Based Wood Stain is:

  • a traditional, pigmented liquid wiping stain
  • Available in 14 colors
  • Can be used as a toner with Arm-R-Seal
  • Apply with a brush or wipe on.

Oil-Based Pre-Stain Conditioner is:

  • Designed to control blotching on hard-to-stain woods.
  • And penetrates the grain to promote uniform acceptance of oil stains.
  • Apply with a brush or wipe on.

Oil-Based Seal-A-Cell Clear is:

  • Formulated with a blend of oils, urethanes, and wax.
  • Is GF’s deepest penetrating close-to-the-wood sealer.
  • And the best choice for highlighting figured wood.
  • Apply with a brush or wipe on.

Hard Wax Oil is:

  • A urethane-solids polymer in a blend of oil & wax.
  • Enhances the natural look of wood.
  • One of our easiest finishes to use.
  • It’s best used with optional GF Hardener to shorten dry time and provide superior durability.
  • This is a maintenance product. Reapply when wear becomes evident.
  • Apply with a white pad or plastic spreader.

 Oil Based Wood Bowl Finish is:

  • A pure urethane formulation.
  • Highlights figured wood beautifully
  • Apply with a brush or wipe on.
INTERIOR MAINTENANCE PRODUCTS

Butcher Block Oil is:

  • A mineral oil formulation.
  • Meets all requirements for use on wooden surfaces that come in contact with food.
  • This is a maintenance product. Reapply when wear becomes evident.
  • Apply with a cloth.

Orange Oil is:

  • A routine cleaner for cured wood finishes
  • Non-combustible with a fresh orange scent
  • Apply with a cloth

Satin Finishing Wax is:

  • A blend of waxes.
  • Produces a soft sheen and feel over any wood finish.
  • Can be used as a polish for rubbing out new finishes OR as a scratch-remover.
  • Apply with a cloth.

No matter what your project is, General Finishes has the right product for you. General Finishes is dedicated to using the highest-quality ingredients in all our products, while testing and advancing our water-based finishes with leading-edge technology.

Learn more about GF’s products at Generalfinishes.com. 

General Finishes: We make tomorrow's finishes today.

 

Related Categories