Enduro Professional Water-Based Black Poly

Enduro Black Pigmented Poly is a professional spray only, high-solids, pigmented water-based coating ideal for cabinets and millwork. Stocked in Black and White, custom colors are available for wholesale customers upon request. White and Clear can be used as tint bases to achieve endless colors. Learn more about General Finishes' entire finishing system of clear and pigmented primers, acrylic and polyurethane clears, pigmented topcoats and water-based stains here: 4 Reasons to Switch to Water-Based Finishes. See our spray tip size recommendations here. Made in the U.S.A. by General Finishes, the Gold Standard for Professional Water-Based Finishes.

enduro water based polyurethane cabinet finish black semi-gloss

Instructions

Step 1: Preparation

All wood projects require preparation sanding. If you skip this critical step, your finish may fail.

Raw Wood

See our video: How To Prep Sand New Wood

  1. Sand with 120-grit sandpaper, followed by 150 or 220-grit.
  2. Remove dust.
Sealed Surface

See our video: How to Prepare Existing Finishes

  1. Scuff clean with a non-woven abrasive pad & 50:50 mix of denatured alcohol & water.
  2. Dry 1-2 hours.
  3. Sand lightly with 220-320-grit sanding sponge.
  4. Remove dust.

Step 2: Priming

Raw Wood & Sealed Surface

GF Black Poly covers great on its own or can be applied over a primed surface. 

Prime with GF Lamp Black Milk Paint to block grain or cover existing color. 

Prime with GF Sanding Sealer for a smooth surface and to fill in voids.

Step 3: How To Apply General Finishes Enduro Black Poly

General Finishes Enduro Black Poly Spray Application Steps for Raw Wood & Sealed Surface

Download 2023 Professional Water Based Product Catalog here.

  1. Black Poly product overview video here.
  2. Watch a comparison of GF paints and pigmented topcoats here.
  3. Work in a well-ventilated area. 
  4. Stir thoroughly to reincorporate solids that have settled to the bottom of the can before and throughout the application process.
  5. Test for color & adhesion over existing sealed surfaces.
  6. Thin as desired with distilled water; start with 5%, increase up to 10% by volume. Increase open time, if needed, with up to 10-15% General Finishes Extender if allowed by local regulations. GF Extender will improve flow and leveling and increase open time, which is helpful in dry climates. California Residents: Adding more than 2% of GF Extender will make the products non-compliant per SCAQMD Regulations. GF assumes no liability for the improper use of these products.    
  7. Ready to spray from container. Apply up to 2 coats of a primer, plus 2 coats of GF Black Poly. Wear NIOSH-approved respiratory & eye protection. 
    • Spray Application: Before spraying, strain through a medium-mesh filter. Spray wet films at 3-5-mil thickness. Medium air cap. Fluid tip sizes Compressed air: .040, HVLP: .043 -.051 or Airless: .1 -.15. Verify tip sizes with equipment supplier. See our spray tip size recommendations here. Read here for more information on spraying techniques. 
      • Face frames: Enduro professional products are engineered to be spray-only but can be successfully applied to cabinet face frames, edges, or drawer fronts with a small cabinet-specific 3/8" nap microfiber roller such as Whizz or AllPro brand. Larger areas may not level. Add 10-20% Extender for improved results. 
  8. If a faster build is desired over raw wood, use General Finishes Sanding Sealer for the first coat, followed by 2 coats of Black Poly.
  9. Dry time to touch: 3+. Dry time to recoat: 1 hour in ideal conditions: 70°F 20°C; 50% humidity. Be sure to allow adequate dry time. You can tell if a water-based finish is dry if it forms a powder when lightly sanded with a fine-grade (220-320) foam sanding pad. If in doubt, wait longer. Rushing the dry time can cause "blush," which is clouding in the finish due to moisture trapped between the layers. Increase dry time if:
    • Humidity is over 80%
    • 3+ coats are applied
    • Thick coats are applied
    • Applying over an existing sealed finish
    • Applying over products from other brands
    • Layering General Finishes water- and oil-based products:
      • Water over oil: Let oil-based products dry 72+hr before applying water-based products
      • Oil over water: Let water-based products dry 24+hr before applying oil-based products
    • To accelerate dry time in humid conditions, add General Finishes Accelerator and work in a space with good ventilation and air movement. If you decide to re-coat before the recommended time, test dryness.
  10. Finish sand between coats with a fine-grade (220-320) foam sanding pad to improve smoothness and adhesion.
  11. Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.

Cure Time
Water-based finishes cure and harden for full use after 21 days in ideal conditions. Avoid placing heavy objects on surfaces that have not completely cured. Treat gently, and do not clean with commercial products during the curing period.

Warning: Do not use water-based products with Linseed Oils or Danish Oils.

Cleanup of Water Based Products

Application tools and materials containing water-based products can be cleaned with soap and water or General Finishes Brush & Gun Cleaner immediately after use.

Product Spills

Spills may be able to be removed from fabric and carpet if cleaned immediately with soap and water.

Disposal

Discard unused product and waste in an environmentally safe manner; check with local fire and health regulation. 

Storage of Water Based Products

Life of Product

General Finishes products do not last forever, even when unopened. They are best used within 1 year. The life of the product may be extended with proper can closure and storage conditions. (see Storage Tips below).

Water-based products can last 3-5 years if the can is unopened, in good condition and stored in correct temperatures.

Product that is 3 years old will not look like product that is 6 months to 1 year old. You will see more stratification or separation as the product ages. Always stir thoroughly before using.

Foul Smell

If your product has a foul smell, it is contaminated and no longer in useable condition.

Clumps & Settling

Gravity can cause some solids to settle on the bottom of the can and slight separation on the top. This is normal. If working with older product stir with a paint mixing attachment on a drill.

If the solids dissolve and clumps smooth out after mixing from the bottom, the product is in good condition for use.

Inability to reincorporate large, chunky lumps after stirring for several minutes is an indication that the product has frozen and can no longer be used.

Storage Tips

See video tutorial: Tips on Storing Leftover Finishes
Water-based finishes crystalize and form a skin due to evaporation when the air-tight seal on a can is broken at first use. The following best practices will increase the life of your product:

  1. Pry open sealed lids with a paint can opener by hooking under the lid's rolled edge. The use of a screwdriver can disfigure the rim and lid, impairing a complete seal. 
  2. Keep lid closed while working. Pour what you will use into a bowl, paper cup, or plate, and close can lid as you work.
  3. Clean the chime of the can thoroughly with a paper towel before closing to create a complete seal. Product falling into the chime can be minimized by using a pouring lid, such as Fitsall. Avoid wiping used brushes on the lid.
  4. Pound the lid in place using a rubber mallet to avoid distorting the chime or lid. Dents in the lid from direct contact with a hammer can impair a complete seal. Alternatively, place a flat piece of wood over can lid and firmly pound shut.
  5. Store in moderate temperatures. Avoid temperatures below 50°F/10°C or above 100°F/26°C. Keep from freezing. Frozen and heat-damaged product cannot be revitalized. Temperature-controlled spaces, such as a basement, are ideal for storage. Do not store product in an attic, garage, in direct sunlight, or next to something warm like a water heater or furnace.
  6. Store can upside down to create a liquid seal, minimize evaporation and reduce the chance of crystallization. Decant remaining product from the can before stirring. 
  7. Decant leftovers to a smaller container when the finish is almost used up. Alternative storage containers for water-based products are plastic FIFO bottles or glass bottles. Do not fill metal-lidded containers completely to prevent them from rusting.

The following water-based product mixtures can be stored:

  1. Product thinned with up to 15% General Finishes Extender or General Finishes Accelerator can be stored, with the exception of thinned General Finishes Water Based Wood Stain.
  2. Mixtures involving colors & sheens within the same product line, such as:
    • High Performance Satin + High Performance Gloss
    • Snow White Milk Paint + Coastal Blue Milk Paint
    • Amber Dye Stain + Merlot Dye Stain

The following product mixtures should NOT be stored:

  • Any water based product with thinned tap water; water often contains bacteria that will adversely affect stored paint.
  • Topcoat + Stain or Paint
  • Milk Paint + Chalk Style Paint
  • Water Based Wood Stain + Dye Stain

Furniture Care and Maintenance

Cure First

You have just finished applying a fine furniture finish. Treat gently until the paint or topcoat have fully cured. Allow 21 days for a water-based finish to cure and 30 days for an oil-based finish to cure before cleaning.

Regular Cleaning and Maintenance
  • Remove dust with a water-dampened cloth. Dust can build up over time and may scratch or dull finishes if not removed regularly. 
  • Remove fingerprints, cooking fumes and smoking residue with mild soap and water. These contaminants will not harm the finish, but they accumulate on surfaces and dull the original luster. 
  • As with all fine furniture finishes, avoid using furniture polish, cleaners or dusting sprays that contain silicone, alcohol, ammonia and anything acidic. Exception: We have successfully cleaned with Clorox wipes for occasional cleanups.
  • Clean up water, alcohol and food spills in a timely manner and use placemats & coasters to protect the finish.
  • Future finishes or touch-ups may not adhere properly or perform as desired over a contaminated surface. Some contaminants, such as silicone, seep through finish into the wood and often cannot be removed.
  • Avoid excessive exposure to direct sunlight, high temperatures or high humidity. These can damage furniture and finishes.

Warnings, Personal Protection & Warranties

Compatibility
Do not use water-based products with Linseed Oils or Danish Oils.
 

Limited Warranty
General Finishes products must be tested to your complete satisfaction before using. General Finishes will not be responsible for color satisfaction, misapplication, nor compatibility with other manufacturers' products. General Finishes will be responsible only for the cost of our products, and not for costs such as labor, damage or project replacement. 

Contamination and Compatibility
Our finishes are engineered as a system and are compatible with each other. General Finishes cannot guarantee an ideal refinish when applying our products on top of or combined with another company's products or over surfaces that have been in contact with waxes, polishes or sprays containing contaminants such as silicone. Test for adherence and aesthetics before beginning. 

Warning
If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log onto www.epa.gov/lead.

FIRST AID:
Seek immediate medical attention if symptoms occur due to the following. EYE CONTACT: Remove any contact lenses. Flush eyes with water for 20+ minutes while lifting upper and lower eyelids. SKIN CONTACT: Wash thoroughly after handling. INHALATION: Move to fresh air and loosen clothing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. INGESTION: Call physician immediately. Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. 

Warning
This product contains a chemical known to the State Of California to cause cancer and birth defects. Do not swallow; first aid: drink water to dilute product. May cause eye or skin irritation; first aid: flush eyes thoroughly with water.

Warning
Keep out of reach of children. Avoid contact with eyes. Keep container tightly closed when not in use. Wash thoroughly after handling.

PERSONAL PROTECTION DURING USE:

Hand protection
Chemical-resistant, impervious gloves complying with an approved standard should be worn when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves still retain their protective properties. It should be noted that the time to breakthrough for any glove material may differ for different manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated.

Eye protection: Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases, or dust. If contact is possible, the following protection should be worn unless the assessment indicates a higher degree of protection: safety glasses with side shields.

Respiratory protection:
Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important use aspects.


Body protection Personal protective equipment for the body should be selected based on the amount and repetition of exposure. It should be approved by a specialist before handling this product.

Environmental exposure controls:
Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation.

Appropriate engineering controls:
Good general ventilation should be sufficient to control worker exposure to airborne contaminants.

Hygiene measures: 
Wash hands, forearms, and face thoroughly after handling chemical products, before eating, smoking, and using the lavatory, and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.
 

Other skin protection: Appropriate footwear and any additional skin protection measures should be selected based on the task being performed.

Specifications

Basic Features
Product Colors Black
Base Type Water
Sheen Satin (25-35), Semi-Gloss (50-60)
Interior or Exterior Interior only
Type Urethane/Acrylic Blend
Application
Coats 3 coats
Application Method Spray
Brushable No
Usable over existing finishes Yes - see product page application instructions.
Sprayable Yes
Spray Tip Sizes HVLP 1.3mm-1.5mm
Dry Time
Dry Time - Touch 30+ min.
Dry Time - Recoat 1+ hr
Dry Time - Light Use 7-10 days
Dry Time - Cure 21 days
Contents
Can Sizes Gallons, 5 Gallon pails
Coverage 450 sq.ft. (41.81 m²) per Gallon
Technical Data
Viscosity Medium
Viscosity (cPs) 600-800
Solids by Weight and Volume Solids by Weight
Satin: 31%
Semi-Gloss: 30%

Solids by Volume
Satin: 28%
Semi-Gloss: 28%
VOC US VOC
Satin: 238.752 g/L
Semi-Gloss: 240.720 g/L
Gloss: 241.470 g/L
Durability
Durability (Highest, High, Medium, Low) High
Hardness (Koenig #) 62
Wear (Taber #) 105.40 mg loss
Water (5 max) 5
Chemical (105 max) 92