Enduro 1K White Poly

Return

Which Topcoat Should I Choose?

General Finishes offers a complete coatings system with a finish for every objective.

General Finishes Professional, Industrial, and OEM Water-Based Topcoats

  • Enduro Professional Tintable 2K Clear Poly
  • Enduro Professional Tintable 2K White Poly
  • Enduro Professional 2K Conversion Varnish
  • Enduro Professional 1K White Poly
  • Enduro Professional 1K Clear Poly
  • Enduro Professional Pre-Cat Lacquer

General Finishes Retail Water-Based Topcoats:

  • High Performance Topcoat
  • Flat Out Flat
  • Enduro-Var Topcoat
  • Exterior 450

General Finishes Exterior Water-Based Topcoats:

  • Enduro Professional Tintable 2K Clear Poly
  • Enduro Professional Tintable 2K White Poly
  • Enduro Professional 2K Conversion Varnish
  • Exterior 450

General Finishes Oil-Based Topcoats

  • Arm-R-Seal 
  • Gel Satin Topcoat
  • Wood Bowl Finish
  • Butcher Block Oil
  • Outdoor Oil

GENERAL PRACTICE:

  1. Oil-based topcoats and ENDURO-VAR will amber over time.
  2. All other water-based and High Performance top coats dry clear.
  3. Never use any water-based topcoat with long oils such as Danish, Tung or Linseed.
  4. Water-based top coats clean up with soap and water. Oil-based topcoats require mineral spirits for cleanup.
  5. If you use water-based topcoats over oil-based finishes, make sure that you wait 72 hours between the two products. It is essential to let the oil finish dry longer.
  6. For more complex projects with many details and corners or large surface areas such as cabinets, we recommend either ARM-R-SEAL liquid oil-based topcoats or water-based topcoats. Large surfaces such as cabinets or tables and complex projects with lots of detail are easier to cover with a liquid topcoat rather than a GEL SATIN topcoat.
  7. Enduro Professional Topcoats are thinner and intended to be sprayed
  8. HIGH PERFORMANCE can be brushed or sprayed. It can be thinned by adding 5-10% distilled water if needed. 

Compare all topcoats

Related Categories


How Do General Finishes Water Based Topcoats Differ?

GF recommends using the least expensive product that will provide the needed performance characteristics. We offer a range of products designed for professional spray applications and brush-on finishes for consumer use.

Compare all GF Topcoats Here

Watch Video: Comparison of All GF Water Based Finishes Here

PROFESSIONAL TOPCOATS

ENDURO PRE CAT LACQUER (Spray only)

Looking for hardness, clarity and fast stack time? Pre Cat Lacquer is the choice. Use in applications where there is little risk of chemical contamination issues from substances such as ketchup, soap, chemical cleaners, or ammonia. This is the perfect spray finish for interior doors, casing, moldings, door jambs and furniture that receives light use. When you think about it, interior doors don't take a lot of wear. You might wipe them down or dust them once in a while but that is about it. PreCat Lacquer is a hard finish that provides excellent build and superior clarity at a phenomenal price point. If you are not finishing a surface such as a tabletop where you anticipate chemical contamination during use, why pay for a more expensive finish?

Dries clear.

Watch Pre Cat Lacquer Product Overview Video Here

ENDURO CLEAR POLY (Spray only)

Poly is the go-to cabinet finish. It has all the durability you need at a lower price point than Conversion Varnish. It is similar to High Performance in test measurements for chemical, water and wear resistance, but HP can be brushed and Clear Poly can't - it is already thinned for spraying. Clear Poly has a bit of an edge over High Performance in overall chemical resistance, a 98 rating vs 92.

Dries clear.

Watch Clear Poly product overview video here

ENDURO CONVERSION VARNISH (2K-Spray only)

This is our top of the line. Conversion Varnish is a post catalyzed high solids, two component urethane formulated for professionals who need the highest level of durability and chemical resistance. Varnish will cure the fastest. Requires NCO Catalyst. It is recommended for commercial applications or extremely high-wear surfaces such as countertops and bar tops

Dries clear.

Watch Conversion Varnish Product Overview Video Here

RETAIL TOPCOATS

HIGH PERFORMANCE (Brush or Spray)

GF's best performing brush on finish with very similar performance testing as our Poly. (High Performance can be thinned for spraying).

Dries clear.

Watch High Performance Product Overview Video Here

FLAT OUT FLAT (Brush or Spray)

Flat Out Flat is formulated with a self cross-linking acrylic, and is designed to mimic the look and feel of a wax finish. Because of the increased matting agents used to create the "Flat look", this finish will have less clarity. Like wax, it dries softer to the touch than High Performance when completely cured, and will show more fingerprints. FOF finish will mark up more easily because of increased matting agents used to reduce the sheen, so it is not recommended for high-use tabletops.

Dries clear.

Watch Flat Out Flat Product Overview Video Here

BOTH PROFESSIONAL AND RETAIL TOPCOATS

ENDURO-VAR (Spray or brush)

Enduro-Var is an oil modified water-based alternative for customers that want the warm look of an oil finish in a water based coating. It looks more like an oil finish than a water coating, and can be sprayed or brushed. The original Enduro-Var adheres well ONLY over WATER STAINS, DYE STAINS, and RAW WOOD. Use over other finishes at your own risk. The new formula of Enduro-Var II is compatible with all GF products and dries to a lighter amber than the previous formula.

Dries Amber

Watch Enduro-Var II Product Overview Video Here

EXTERIOR 45O TOPCOAT

Exterior 450 provides a clear drying tough, protective finish that will withstand the rigors of the sun, rain, and wind. It is suitable for vertical surfaces such as fences, patio furniture, garage doors, entrance doors, outdoor kitchens and interior windows. It is not recommended as a deck finish. Fortified with UV absorbers to stabilize the finish, Exterior 450's built-in mildewcide retards mold and mildew growth.

Dries Clear

Watch Exterior 450 Topcoat Overview Video Here

Related Categories


*What Is the Best Way to Store Water Based Finishes?

LIFE OF PRODUCT

Water-based products do not last forever, even when unopened. General Finishes products are best used within 1 year of the manufacture date listed on the bottom of the can. The life of the product may be extended to 2-3 years with proper care and storage.

SETTLING

Gravity can cause some solids to settle on the bottom of the can and slight separation on the top. This is normal. If working with older paint, use a paint mixing attachment on a drill. If the solids dissolve and clumps smooth out after mixing from the bottom, the product is in good condition for use.

STORAGE TIPS

See video tutorial: Tips on Storing Leftover Finishes 
Water-based finishes crystalize and form a skin due to evaporation when the air-tight seal on a can is broken at first use. The following best practices will increase the life of your product:

  1. Pry open sealed lid(s) with a paint can opener by hooking under the lid's rolled edge. The use of a screwdriver can disfigure the rim and lid, impairing a complete seal.
  2. Keep lid(s) closed while working. Pour what you will use into a bowl, paper cup, or plate, and close can lid as you work.
  3. CLEAN the chime of the can(s) thoroughly with a paper towel before closing to create a complete seal. Paint in the chime can be minimized by using a pouring lid, such as Fitsall. Avoid wiping used brushes on the lid.
  4. Pound the lid(s) in place using a rubber mallet to avoid distorting the chime or lid. Dents in the lid from direct contact with a hammer can impair a complete seal. Alternatively, place a flat piece of wood over can lid and firmly pound shut.
  5. Store in moderate temperatures. Avoid temperatures below 50*F/10*C or above 80*F/26*C. Frozen and heat-damaged product cannot be revitalized. Temperature-controlled spaces, such as a basement, are ideal for storage. Do not store product in an attic, garage, in direct sunlight, or next to something warm like a water heater or furnace.
  6. Store the can(s) upside down to create a liquid seal, minimize evaporation and reduce the chance of crystallization. Decant remaining product from the can before stirring.
  7. Decant leftovers to a smaller container when the finish is almost used up. Alternative storage containers for water-based products are plastic FIFO bottles or glass bottles. Do not fill metal-lidded containers completely to prevent them from rusting.

The following water-based product mixtures can be stored:

  1. Product combined with up to 15% General Finishes Extender or General Finishes Accelerator can be stored, with the exception of thinned General Finishes Water Based Wood Stain.
  2. Mixtures involving colors & sheens within the same product line, such as:
    • High Performance Satin + High Performance Gloss
    • Snow White Milk Paint + Coastal Blue Milk Paint
    • Amber Dye Stain + Merlot Dye Stain

The following product mixtures should NOT be stored:

  • Any water-based product with thinned tap water; water often contains bacteria that will adversely affect stored paint.
  • Topcoat + Stain or Paint
  • Milk Paint + Chalk Style Paint
  • Water
  • Water-Based Wood Stain + Dye Stain

Related Categories


*Why Do I Sometimes Get Metal Marks On Cabinets I Have Painted with White Poly?

This is very common in pigment coatings and paints. It is called metal marking and it is a characteristic that is very difficult to eliminate.

You can even see it in dinnerware like white plates. We usually test with wedding rings and forks. It a constant focus and improvement project for General Finishes, especially the whites. The difference with tinted clear is that the amount of pigment varies from color to color, so sometime it will occur with the lighter paints.

Related Categories


What is the best, most durable paint for cabinets? Check out Water-Based Tintable 2K Clear and White Poly

Enduro 2K Tintable 2K White and 2K Clear Poly

Enduro tintable 2K Clear poly drying under IR

Superior water-based Enduro Tintable 2K Polys made in Wisconsin for professional, industrial, and OEM users. We hope you try it out; you’ll like it.

The term 2K references a product that is a 2-component polyurethane specifically catalyzed with Isocyanate to crosslink the polymer fully, which provides superior performance 1K coatings hardened PolyAzuradine or Carbodiiamide. To create Enduro Tintable 2K, General Finishes tested over 30 polymers, resins, and other ingredients sourced from around the world. 

These new coatings are engineered to prevent the biggest frustrations for today's professional, industrial and OEM users providing ultimate durability for interior/exterior use. 

General Finishes goes hard for great chemistry, so you don't have to worry when your clients are tough on the paint. Paired with Tintable 2K Clear Poly, you have a dynamic duo of 2 component finishes, the most durable interior/exterior coatings General Finishes has ever created. You can apply confidently, knowing that you are giving your customer the best the industry offers. 

Perfect for new or remodeled cabinets, furniture, woodwork, pre-primed steel, fiberglass, and exterior projects. Made in the U.S.A.

KEY FEATURES

  1. Ease of application. Whether in a shop or on-site, Enduro 2K is designed to flow and level for Professionals/Industrial users that apply with AAA, HVLP, Airless, or flatline systems.
  2. Tintable to any major manufacturer's color deck. Enduro 2K hits the deepest darks, the bright whites, and everything in between. General Finishes recommends ColourFal Zero colorants.
  3. Higher gloss standards for white and clear, with 90+ degrees on a 60-degree angle.
  4. Fast production time: You can spray 3-4 coats of Enduro 2K and sand in between coats in one day. Enduro 2K cures for use in 5 days.
  5. Fast film build: Enduro 2K'S are engineered with a combo of larger and smaller-sized resin particles, which, when combined with the catalyst, allows for a thicker, quicker film build than any 1K. It provides a better vertical hang when spraying built-in surfaces on-site, with fewer drips or sags.
  6. Water and chemical resistance: Combining our new resin with catalyzation allows Enduro 2K to hit a commercial level of water and chemical resistance that *exceeds industry requirements and guidelines”. This is the perfect coating to stand the test of time on Wisconsin bar tops.
  7. Excellent adhesion properties on properly cleaned and prepped wood, plastics, fiberglass, and pre-rimed steel. (It Sticks).
  8. Exterior use: This new finish has an unusual balance of durability and flexibility, making it the professional’s choice for outdoor projects such as doors, benches, furniture, and tables. Do not use on deck surfaces.
  9. Consistency. General Finishes prides itself on superior quality control to meet and exceed the customer’s expectations.

Available in Flat, Satin, Semi-gloss, and Gloss

Related Categories